How To Install Lead Flashing On A Pitched Roof In Bracknell

If you are looking to install lead flashing on your pitched roof in Bracknell, then look no further than A1 Roofing Bracknell. We are a trusted roofing company with years of experience in providing top-notch roofing solutions in Bracknell and the surrounding areas. In this article, we will guide you on how to install lead flashing on your pitched roof and make sure it is done perfectly.

Introduction To Lead Flashing

Lead flashing is a roofing material made of malleable sheets of lead that are used to seal joints, edges, and corners in a roof. It acts as a weatherproof barrier, protecting your roof from water penetration. Lead flashing has been in use for centuries and is still one of the most popular roofing materials due to its durability and resilience.

Types Of Lead Flashing

There are several types of lead flashing available in the market, including code 3, code 4, code 5, and code 6. The codes refer to the thickness of the lead sheets, with code 3 being the thinnest and code 6 being the thickest. The type of lead flashing you choose to use will depend on the pitch of your roof, the location of the flashing, and the roofing materials used.

Step-By-Step Guide To Installing Lead Flashing

Before you start the installation process, you will need to gather the necessary tools and materials. These include:

• Lead flashing
• Nails
• Hammer
• Sealant
• Gloves
• Safety goggles
• Cutting tools (tin snips, lead knife, or bench shears)
• Measuring tape

Step 1: Measure The Area

Measure the length of the area that you want to cover with the lead flashing, adding an additional 100mm on each side for overlaps. Then, measure the width of the area and cut the lead sheet to the appropriate size.

Step 2: Prepare The Brickwork

Use a sealant to prime the brickwork and ensure it is adequately prepared for the lead flashing.

Step 3: Position The Lead Flashing

Place the lead flashing on the prepared brickwork, making sure it is flush with the wall. Use a hammer and nails to secure the lead flashing onto the brickwork.

Step 4: Create Overlaps

It is essential to create overlaps between the lead flashing sheets. Overlaps should be at least 100mm and covered in sealant to join the sheets together.

Step 5: Fold The Lead

Fold the lead sheet to ensure it is flush with the roof surface. Use a lead knife to create a neat, straight edge on the lead.

Step 6: Secure The Flashing

Use nails to secure the lead flashing to the roof surface. Nails should be long enough to penetrate both the lead flashing and the underlying surface but short enough not to create a hazard.

Step 7: Seal The Joints

Use sealant to create a watertight seal around the edges of the lead flashing. This will ensure that the roof is protected from water penetration.

Step 8: Finish

Finally, inspect the lead flashing to ensure that it is securely fitted and watertight. Any areas where the lead flashing is not adequately secured can lead to leaks in the future.

A1 Roofing Bracknell - Your Trusted Roofing Company In Bracknell

At A1 Roofing Bracknell, we specialize in providing a wide range of roofing services in Bracknell and the surrounding areas. Our team of expert roofers is trained and experienced in installing lead flashing on pitched roofs, ensuring you get high-quality roofing solutions that are built to last. We take pride in our attention to detail and workmanship, ensuring every job we undertake is completed to the highest standard.

If you need help with installing lead flashing on your pitched roof in Bracknell, do not hesitate to contact us. Our team is always on hand to offer expert advice and guidance and will be happy to discuss your roofing needs.

Contact Us

Contact A1 Roofing Bracknell today for all your roofing needs in Bracknell and the surrounding areas. Call us on 01344 534049, email us at [email protected], or visit our website at a1-roofing-bracknell.co.uk for more information.